Sku: XPW100100K-01

AUD$387.75
Availability: Many In Stock
Sku: XPW100100K-01
WiFi
Lantronix

xPico® Wi-Fi® Development Kit

 

 

The xPico Wi-Fi evaluation board provides a test platform for the Lantronix xPico device server products. The evaluation board uses either 5V power from a USB device port connector or power supplied to the Ethernet connector via PoE. The evaluation board also provides a header for connection to a 2.2V to 5.5V external source, such as a battery. The Evaluation Kit includes a 5V wall adapter with a USB plug to allow powering the evaluation board from a standard power strip. The evaluation board includes all necessary regulators to power the 3.3V xPico module. The evaluation board has the following features:

♦ One DB9 serial port connector with a multi-protocol RS232, RS422, RS485 transceiver at rates up to 1Mbps. Serial port modes are configured by on-board jumpers.

♦ A second RS232 serial port is available on a header.

♦ One RJ45 10/100 Ethernet port with an integrated PoE regulator to allow powering from standard POE PSE. (POE works with Ethernet xPico modules only)

♦ One Mini-Type B USB device port connector for 5V input power. This port also has an integrated USB-to-serial converter. The USB-to-serial converter can be connected to the xPico second serial port via a board jumper setting.

♦ A second Mini-type B USB device port is available for connection to the xPico module USB device port. (Currently available on xPico Wi-Fi only)

♦ LEDs for the xPico Ethernet, WLAN, and System status outputs along with two additional LEDs that can be driven via jumper wire.

♦ Access to all logic level IO signals on the xPico via header pins for measurements and connections to other places.

 

xPico Wi-Fi Evaluation Kit Contents

♦ xPico Wi-Fi Module 

♦ xPico Evaluation Board

♦ 5V Wall Adaptor

♦ xPico Mounting Quick Clip

♦ 40-pin Connector Sample

♦ 2 dBi Swivel Type Antenna and U.FL to RP SMA Cable

♦ 2.5 dBi PCB Strip Antenna with U.FL cable

 

Features & Specifications

Wireless LAN Interface

  • IEEE 802.11 b/g and IEEE 802.11n (single stream) WLAN interface (2.4 GHz only)
  • IEEE 802.11 d/h/i/j/k/w/r
  • WPS 2.0 support
  • u.FL connector for external antenna

Serial Interface

  • Two Serial CMOS Ports (3.3V, 5V tolerant)
  • 300 to 921.6 Kbps
  • Flow control XON/XOFF, RTS/CTS (SPort 1 only)
  • Lantronix tunneling application (SPort 1 only)

Host Interface

  • Dual Serial Port, SPI, USB 2.0 (device)
  • 8 GPIO

Network Protocols

  • TCP/IP, UDP/IP, DHCP, ARP, ICMP, DHCP, Auto-IP, DNS, SNMPv1, TFTP

Networking Capabilities

  • Soft Access Point with DHCP Server
  • Lantronix SmartRoam™ Technology continually tracks Wi-Fi signal strength within range, along with preauthentication and caching resulting in smooth and automatic transition to access points without delay.
  • QuickConnect: Dynamic Profiles facilitate easy and rapid connections to access points

Management and Control

  • Web Server - Landing Page
  • CLI (Serial Monitor Port), Telnet
  • XML import and Export (XCR)
  • Field upgradable firmware (OTA)

Security

  • IEEE 802.11i Support – WPA-Personal, WPA2-Personal
  • 256-bit AES Encryption

Architecture

  • ARM Cortex M3 class processor with on-chip Flash and SRAM
  • 1MB Flash and 128 KB SRAM
  • SPI Flash storage

Power

  • Input Voltage: 3.3VDC
  • Low power consumption of approximately 6μA standby

Physical Interface

  • 40-pin Board-to-Board SMT Connector

Environmental

  • Operating Temp: -40° to +85° C
    • For operation over +70° C a thermal pad is required
  • Storage Temp: -40° to +85° C
  • Relative Humidity: 0% to 90% non-condensing

Certifications

  • FCC Class B, UL and EN EMC, Japan

Packaging

  • Dimensions: 24mm (L) x 16.5mm (W) x 5.64mm (H)
  • Weight: 2.5g

Warranty

  • 5-Year Limited


Documentation

XPW100100K-01 - Lantronix Xpico WiFi Development Kit

Sku: XPW100100K-01

Just added to your wishlist:
My Wishlist
You've just added this product to the cart:
Go to cart page